 |
DOUBLE BACK CHECK FILLER VALVE
|
Complete with a 1-3/4" ACME filling connection and 3/4" NPT tank thread. This valve has a high filling capacity and an all forged, two-piece body. Used primarily for ASME motor fuel tanks or portable DOT cylinders. Filling rate is approximately 20 GPM with a 10 lb. differential. |
|
CHECK FILLER VALVE |
50118 |
$41.95 |
 |
|
REPLACEMENT YELLOW CAP |
50159 |
$3.99 |
|
|
REPLACEMENT VALVE WASHER |
54425 |
$0.69 |
|
|
|
|
|
|
|
|
|
|
|
 |
POL DUST CAP
|
Use on new style propane tank valve. Helps keep cylinder valve clean when not in use. Made in U.S.A. |
50321 |
$1.99 |
|
|
|
 |
PV-10A OUTAGE VALVE
|
Fixed liquid level gauges indicate maximum filling level as permitted by pamphlet #58. in use, a white spray indicates the liquid level has been reached. Used in containers having a liquid level tube welded in the vessel, or where mounting is to be done on the maximum allowable filling level. Gauge has a #54 drill size orfice. |
50007 |
$2.99 |
|
|
|
 |
SHERWOOD INLINE OPD VALVE
|
The inline OPD valve by Sherwood doesn't restrict valve output and doesn't slow down purge. It's all inline-there is no output-limitating orfice inside, and the floats inline (no awkward float arm). Maximum output is 1.9 million BTU per hour at 100 lbs pressure. Allows full strength operation of any size torch, heater or other appliance. RV owners can be comfortable, even at sub zero temperatures. Purges quickly, just as fast as if the OPD wasn't there. The unit is sturdy and compact, easy to store, handle and install. Sherwoods OPD valve allows a matchup with a cylinders required dip tube length. Inlet 3/4"NGT; outlet: female POL and 1-5/16" male ACME. |
|
OPD VALVE FOR 20# STEEL OR 10# ALUMINUM CYLINDER (RECOMMENDED DIP TUBE 4"L) |
56775 |
$28.95 |
|
|
REPLACEMENT HANDWHEEL |
50207 |
$1.79 |
|
|
|
 |
RECTORSEAL #5 PIPE THREAD SEALANT
|
Slow dry, soft set, non-seizing...breaks out easily without damaging threads. Ideal for gas, water, oil or butane. |
|
RECTORSEAL SEALANT 1-3/4 OZ. TUBE |
50426 |
$4.29 |
|
|
RECTORSEAL SEALANT 1/4 PINT CAN |
50280 |
$9.49 |
|
|
|
 |
MARSHALL EXCESS FLOW P.O.L. SPUD AND NUT
|
The P.O.L. Adapter ("Spud & Nut") is required to convey LP gas to the regulator. Excess-flow type, required for use on RVs, restricts the flow of escaping gas in the event the regulator is broken off at the P.O.L. However, it is not designed to detect a leak or totally shut off system in the event of a leak or failure of the regulator. 1/4" MPT x excess flow P.O.L. 7/8" hex nut. |
50185 |
$10.59 |
|
|
|
 |
MARSHALL GAS REGULATOR Z-BRACKET
|
Predrilled to attach to all Marshall Gas Regulators horizontally or vertically. Allows the regulator to be mounted from the front to any surface. |
50845 |
$0.99 |
|
|
|
